Hampton Bay 36946 Instalační příručka

Procházejte online nebo si stáhněte Instalační příručka pro Domácí fanoušci Hampton Bay 36946. Hampton Bay 36946 Installation Guide Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 2 - 52” Coleburn

8.Finishing the FanInstallationSTANDARD CEILING MOUNTINGAlign the locking slots of the ceiling canopy 1. with the two screws in the mounting plate. Pu

Strany 3 - Safety Rules 1

9.Attaching the Light Kit CAUTION - To reduce the risk of electrical shock, disconnect the electrical supply circuit to the fan before ins

Strany 4 - 2. Unpacking Your Fan

10.Figure 16Blade BalancingThe following procedure should correct most fan wobble. Check after each step.Check that all blade and blade bra

Strany 5 - Installing Your Fan 3

Operating Your Fan 11. Turn on the power and check the operation of the fan. The pull chain controls the fan speed as follows: 1 pull - High, 2

Strany 6 - Hanging the Fan

12. Care of Your FanHere are some suggestions to help you maintain your fan.Because of the fan’s natural movement, 1. some connections m

Strany 7 - “Close-to-Ceiling” Mounting

Specications 13. FAN SIZE SPEED VOLTS AMPS WATTS RPM CFM N.W. G.W. C.F.52”Low 120 0.24 13 70 169021.6 Lbs24.2 Lbs1.73Med 120 0.34 26 104 2591High 120

Strany 8 - Installing Fan to

Hampton Bay Lifetime Limited WarrantyLifetime Warranty on MotorHampton Bay warrants the fan motor to be free from defects in workmanship and material

Strany 9 - Connections

52” ColeburnCeiling Fan by Hampton Bay(3) 60-Watt Equivalent MediumBase CFL Bulbs Included3-Speed Reverse Function forYear-Round Comfort and SavingsAp

Strany 10 - Fan Blades

Safety Rules ... 1Unpacking Your Fan ... 2Installing Your Fan ... 3Operating Your F

Strany 11 - Fan Without Light Kit

Blade Attachment Hardware a. (15 screws)Mounting Hardware b. (1 bolt, 1 clevis pin, 1 rubber gasket) Electrical Hardware & Balancing Kit c. (3 pl

Strany 12 - Blade Balancing

Installing Your Fan 3. Tools RequiredPhillips screwdriver, adjustable wrench, step ladder, and wire cutters.Mounting OptionsIf there isn’t an

Strany 13 - Operating Your Fan 11

Remove the mounting plate from the 2. canopy by loosening the four screws on the top of the canopy. Remove the two non-slotted screws and

Strany 14 - Care of Your Fan

5.Figure 9Figure 10FAILURE TO COMPLETELY TIGHTEN THE THREE SCREWS IN STEP 7 COULD RESULT IN FAN LOOSENING AND POSSIBLY FALLING.“Close-to-Ceiling”

Strany 15 - Specications 13

6.Installing Fan tothe Outlet BoxPass the 120-volt supply wires through the 1. center hole in the ceiling mounting plate as shown in Figure 11.Install

Strany 16 - 14. Warranty Information

7.SUPPLY CIRCUITBLACKWHITEGround toDownrodOutlet BoxBLUEBLACKWHITEGREENBLUEBLACKWHITEWHITEGreenGroundingLeadMaking the Electrical ConnectionsREMEMBER

Komentáře k této Příručce

Žádné komentáře